Newsletter 542: Cyber Monday... and 95November 24^th, 2022

Do you want to build the test version of the Jordan Ford J191? Or perhaps the brazillian decoration? Maybe San Marino? Or even Monaco? All of these (plus some more!) are included in this spectacular decal sheet from Studio27. Forget that incomplete and yellowish decals of your old kit and treat yourself building your Jordan with the level of detail it deserves. New re-edition!!!

Decal sheet with everything necessary to make the version of the Mitsubishi Lancer Evo IV Group A with which Tommi Mäkinen participated in the 1997 and 1998 editions of the Monte Carlo rally, wearing the number #1 in both cases, getting a third place in 1997 and leaving in 1998, in what was the premiere with his new co-driver. The decal sheet also makes it possible to make the second unit, renamed Carisma, used by Richard Burns in the same rally in 1998, an edition in which the names of the drivers also began to be seen on the side rear windows.

Clutch assembly for the Tamiya kit of the Moto GP Suzuki GSX-RR, printed in two separate pieces to facilitate the painting of the clutch discs and the casing.

Detailed 3D printed chain for Tamiya's model kit of the Yamaha YZR-RM1, Yamaha's super sports bike.

Set of 49 1.2mm diameter bolts and 49 0.8mm diameter bolts, designed to replace and enhance the appearance of the plastic molded bolt heads found on 1/12 scale motorcycle fairings. No more bad looking screw decals, no more hassle with painting or masking!!!

Detailed 3D printed chain for Tamiya's model kit of the Honda CBR1000RR-R Fireblade SP.

Detailed chain printed with 3D technology for the Honda RC213V Tamiya model kit. The two grilles that go at the end of the two exhaust outlets are also included.

Before the logical evolution led to other more complex systems, racing vehicles were equipped with cumbersome radio transmitters. Printed in 3D, the parts included with this reference make up the basic equipment, with a transmitter base, antenna and microphone. Includes 10 cm of black cable with a diameter of 0.2 mm. The transmitter can also be used for off-road scale models, trucks, and even (why not?) military vehicles. Over and out!

Set with three sets of sports shock absorbers with different sizes and mountings, to be used on both the front and rear axles. The body of the shock absorbers simulates the threading and the nut for height adjustment. The final height of the assembly is achieved by modifying the position of the shock absorber shaft. The set includes a 0.2 mm diameter cable to recreate the springs.

If there is a characteristic element when it comes to detailing the engines of our models, these are the spark plug cables, and although the engines currently use complex electronic management systems, in the past the spark was generated by an ignition distributor with as many cables (plus one) as cylinders had the engine. If you're detailing a "classic" engine you might find these 3D printed two-piece distributors, designed for eight-cylinder engines and complete with wiring in three different colors, to be of great use to you.

If there is a characteristic element when it comes to detailing the engines of our models, these are the spark plug cables, and although the engines currently use complex electronic management systems, in the past the spark was generated by an ignition distributor with as many cables (plus one) as cylinders had the engine. If you're detailing a "classic" engine, you might find these 3D printed two-piece distributors, designed for six-cylinder engines and complete with wiring in three different colors,,to be of great use to you.

If there is a characteristic element when it comes to detailing the engines of our models, these are the spark plug cables, and although the engines currently use complex electronic management systems, in the past the spark was generated by an ignition distributor with as many cables (plus one) as cylinders had the engine. If you're detailing a "classic" engine you might find these 3D printed two-piece distributors, designed for four-cylinder engines and complete with wiring in three different colors, to be of great use to you.

It is common for racing vehicles to have some specific containers and jars in the engine compartment area, normally made of aluminium. This set includes six of the most common designs. Essential!

This reference includes 3 pairs of brackets featuring different designs to build the strut reinforcement bars, also known as anti-torsion bars. The supports are printed with 3D technology, while a plastic tube is included for the central bar so it can be cut down to fit the width of the model.

Lovers of off-road models, or those who want to build in detail assistance vehicles used for the rescue of other vehicles, will appreciate this 3D printed winch for their models. The winch comes separated into three pieces, the electric motor, the hook and the guide rollers, which allow the modeler to configure the scene with different lengths of string (not included). Do you already know in which model to incorporate it?

Fire extinguisher printed with 3D technology, which includes a photo-etched plate to build its bracket.

Batteries used in competition are slightly different from those used in street vehicles, as they seek to weigh as little as possible and take up as little space as possible. For those who need a battery of these characteristics in the detailing of their kits, this compact battery printed with 3D technology meets all the requirements.

This 3D printed hydraulic handbrake includes, in addition to the vertical actuation lever, the anchoring base to the bodywork, the pump bellows and the pump itself with its connection for the brake pipe and the fluid reservoir, What great definition and detail!

Set of 4 different types of 3D printed foam air filters, featuring the most common designs used in engine builds.

Large size 3D printed oil radiator. It incorporates the oil inlet and outlet connections at the top of the cooler.

Have you ever had the feeling while detailing the engine bay of a road car that you are always missing the same parts? For us, yes, and that is why the appearance of two of these parts, a cooling system expansion tank and a brake booster assembly with pump and tank, have seemed a success, printed with 3D technology and with great detail.

Wheel pin adapter set to easily convert Aoshima rim models to be mounted on Tamiya and Beemax kits.

Wheel pin adapter set to easily convert StreetBlisters rim models to be mounted on Tamiya and Beemax kits.

Do you want to equip your model with good audio equipment? You will need several speakers, a subwoofer and an audio unit, and with these 3D printed parts you will have no problem incorporating them.

Single plane rear spoiler for GT vehicles, with two types of supports to be able to position the spoiler at different heights.

Single plane rear wing for GT vehicles, with three types of narrow brackets to be able to position the wing at different heights and distances from the bodywork.

3 different types of towing hooks/eyes mounted on racing cars for removal by crane in the event of an incident. 3D printed,

Set of two 3D printed turbochargers, with the turbine and compressor shell parts printed separately.

When preparing a turbocharged engine, it is almost mandatory to also improve the intercooler, an element responsible for cooling the intake air before it is introduced into the engine. If your model needs to mount this component as well, this 3D printed intercooler can come in handy. The intercooler measures 25 x 9,8mm.

Set of LED light bars with different lengths, plus two hexagonal auxiliary headlights that would be mounted as corner holders. The corresponding light bar supports and the transparent resin strips are included. Due to their size, they are ideal for off-road models, or for assistance vehicles used to rescue other vehicles.

It is becoming more and more common to incorporate some decorative elements into our montages that enrich the scenes, and since we like vehicles with engines and gears, why not incorporate some of these 3D printed containers and containers, where the oils, refrigerants and cleaning products, necessary for the correct maintenance of our vehicle, would normally be?

For the workshop, to put in a delivery cart, to place next to a goods van, to place in the back of a pickup... there are many scenes where it occurs to us that these storage boxes printed with everything detail with 3D technology could be ideal. What do you also think of many others?

Set of four four-bolt rims with separate adapter hub and decal sheet to decorate the center hub cap. The rims come without tires. Each of the rims has an approximate wide of 10.65 mm.

Set of four Enkei 5-bolt rims with two separate adapter hub sets for use with different kit manufacturers, and a decal sheet to decorate the hub center cap. The rims come without tires. Each of the rims is approximately 20.6 mm in diameter and 12 mm wide.

Set of four classic five-bolt sheet metal rims. The rims come without tires. Each of the rims has an approximate wide of 11.2 mm.

Spectacular set of four five-bolt Ferrada rims with two sets of separate adapter hubs to be used with different model manufacturers, and with a decal sheet to decorate the center cap of the hub. The rims are printed in two pieces, with separate rim and core, and come without tires. Each of the rims has a diameter of about 20.6 mm and a width of about 14 mm.